Archive

Posts Tagged ‘reset’

Cisco Catalyst Password Reset

October 23, 2014 Leave a comment

In the event that you forgot any remote login password, there is no way to recover the password but there is away to change the password and retail all the configuration.

1) Put the switch in ROMmon state.
2) Initialize the switch with command flash_init
3) Rename the flash:config.text file to flash:config.text.renamed
4) Boot the switch.
5) After rebooting, the switch is back to factory setting, copy the renamed config file to the running config.
6) Amend the remote password, save and reload.

Advertisements
Categories: Cisco, Switch Tags: , ,

%C4K_SWITCHMANAGER-4-S2WERRORREPORT

November 14, 2012 Leave a comment

Recently there is a lightning strike in the office area and caused some of the LAN points to loose PoE function.

Those affected interfaces on core catalyst 4500 series had error like this:
%C4K_SWITCHMANAGER-4-S2WERRORREPORT: (Suppressed 9 times)PimEthAutoNeg: S2w Read/Write Error for port Fa6/6

Resolution: Do a hardware module reset.
Cisco# hw-module module 6 reset

The command will switch OFF & ON whichever module slot specified.

Categories: Switch Tags: , ,

Reset Outlook language to English

August 10, 2010 Leave a comment

Start > run > Outlook.exe /resetfoldernames

Categories: windows Tags: ,

Reset Internet Protocol (TCP/IP)

July 26, 2010 Leave a comment

One of the components of the Internet connection on your computer is a built-in set of instructions called TCP/IP. TCP/IP can sometimes become damaged or corrupted. If you cannot connect to the Internet and you have tried all other methods to resolve the problem, TCP/IP might be causing it.

Because TCP/IP is a core component of Windows, you cannot remove it. However, you can reset TCP/IP to its original state by using the NetShell utility (netsh).

Follow these steps to use the reset command to reset TCP/IP manually:

  1. Open a command prompt, click Start then click Run. Type cmd into the box and press ENTER.
  2. At the command prompt, type the following command and press ENTER:
    netsh int ip reset reset.log
  3. Reboot the computer.

When you run the reset command, it rewrites two registry keys that are used by TCP/IP. This has the same result as removing and reinstalling the protocol. The reset command rewrites the following registry key:

SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\ 
SYSTEM\CurrentControlSet\Services\DHCP\Parameters\
Categories: Networking Tags: , ,

Reset Cisco Aironet 1200 series

May 10, 2010 Leave a comment

Step 0: Console to the AP (make sure you’re always console to the AP thru out)
Step 1: Disconnect power from AP.
Step 2: Press and hold the MODE button while you reconnect power to the AP.
Step 3: Hold the MODE button until the Status LED turns amber (approximately 1 to 2 sec), and release the button.
Step 4: After the AP reboots, you must re-configure the AP by using CLI or GUI
*Note: The AP is configured with the factory default values including IP address. The default username and password are Cisco/Cisco
Categories: Cisco, Wireless Tags: , ,

Factory reset Cisco AP 1140 cli

May 3, 2010 2 comments

Factory reset Cisco AP 1140 via cli:

**This the command below will reset everything but the IP addr:
ap(config)# erase startup-config
ap# reload

**To change the ethernet interface to DHCP client:
ap(config)# interface BVI1
ap(config-if)# ip address dhcp client-id GigabitEthernet0
ap# write memory

Categories: Cisco, Wireless Tags: , , ,

Factory reset Cisco switch

February 1, 2010 Leave a comment

Console or telnet into the switch:

switch> enable

switch# erase startup-config

switch# delete flash:vlan.dat

switch# reload

After reload, your switch configuration will be in factory default environment.